RV Water Heater Anode Rod 2-Pack, Galvanized 9.25”x3/4” NPT
RV Water Heater Anode Rod 2-Pack, Galvanized 9.25”x3/4” NPT
BUNDLE & SAVE
Couldn't load pickup availability
Safe & Secure Checkout
256-bit SSL encryption
protects every order.
30-Day Guarantee
Love it or get a full refund.
No hassle.
RV Water Heater Anode Rod 2-Pack, Galvanized 9.25”x3/4” NPT
Protect the tank.
Keep the hot water.
Two AZ31 magnesium anode rods with galvanized hex heads, made to the exact 9.25" × 3/4" NPT size of Suburban RV water heaters. One goes in today. The spare rides along for next season.

The part most RV owners never check
Behind the small exterior door of every Suburban water heater is a steel tank lined with glass enamel. Over time, heat and pressure open tiny cracks in that lining, and the water starts working on the bare steel underneath.
The anode rod is what stops it. It's also easy to forget, because you can't see it until you pull it out. Plenty of owners find theirs worn down to a bare wire the first time they look.
Checking the rod
One socket and a few minutes, twice a year.
Skipping it
A rusted-out tank. In most cases that means a whole new water heater, which can cost $800 or more.

It wears out so your tank doesn't
Magnesium is more electrochemically active than steel. Inside the tank, corrosion goes after the most active metal it can reach, so the rod slowly dissolves while the steel stays intact.
That's why a worn rod is good news. It means the rod did its job. The only real problem is a rod that's gone.
Magnesium is the factory-standard anode material for Suburban heaters because it gives the strongest protection across the widest range of water.

Made to the Suburban spec
Every dimension matches the anode port your heater already has, so there's nothing to adapt.

Check your heater before you order

Fits
Suburban tank-style water heaters with a 3/4" NPT anode port, including the SW6DE, SW10DE and SW12DE (6, 10 and 12 gallon).
Not for
Atwood and Dometic heaters. Their aluminum tanks use a plastic drain plug instead of an anode rod.
Built for campground water
Many campgrounds run on well water, and well water is often hard. Minerals build up on threads and speed up rust, which is how anode plugs end up seized in the tank.
The galvanized hex head on each rod resists rust, helping it come out cleanly at your next service.

Hard or mineral-rich water also wears magnesium faster. That's the rod doing its job, and it's the reason to check it twice a year.
How to replace it
No special tools beyond a 1-1/16" socket. Most of the time goes into draining and flushing.
-
Turn the heater off and let it cool
Switch off both gas and electric, then give the water time to cool so nothing comes out hot.
-
Shut off the water and release pressure
Turn off the pump or city water, then open a hot faucet or lift the pressure relief valve. Skip this and the tank will spray the moment the plug comes loose.
-
Remove the old rod
Use a 1-1/16" six-point socket and turn counterclockwise. A breaker bar helps if it hasn't been out in a while.
-
Flush the tank
Let it drain, then rinse through the port until the water runs clear. You'll wash out scale and old anode debris.
-
Wrap the new threads
Clean the tank threads, then wrap 2–3 turns of the included PTFE tape clockwise around the new rod's threads.
-
Start it by hand
Hold the rod level and turn the first few threads by hand to avoid cross-threading. Then snug it with the socket. The threads are tapered, so stop once it seals.
-
Refill before you power on
Turn the water back on with a hot faucet open until it flows steadily, check the plug for leaks, then turn the heater back on.
Never turn the heater on with an empty tank. Running dry can burn out the electric heating element in seconds.
Keep it on schedule
| Every 6 months | Pull the rod and look at it. Check more often if you camp on hard water. |
|---|---|
| About half worn | Plan your swap and keep the spare ready. |
| 75% gone or bare wire showing | Replace it now. |
| Before winter storage | Drain the tank, then put a rod back in. An open port lets the tank threads rust. |
From the mesa to the mountains
MESALODE is named for the flat-topped mesas of the American road trip and the veins of metal ore beneath them. We focus on the small, hard-working parts that keep an RV comfortable far from home, starting with the one that protects your hot water.
What's in the box

- 2 × AZ31 magnesium anode rods, 9.25" × 3/4" NPT with galvanized 1-1/16" hex heads
- 1 × roll of PTFE thread-seal tape
- Socket not included. Any standard 1-1/16" six-point socket fits.
30-day money-back guarantee
Wrong fit or not happy with it? Contact us within 30 days of delivery and we'll make it right with a refund.
Questions RV owners ask
Will this fit my Atwood or Dometic water heater?
No. Atwood and Dometic heaters use aluminum tanks with a plastic drain plug and don't take a 3/4" anode rod. This rod is for Suburban tank-style heaters.
Magnesium or aluminum: which should I use?
Magnesium gives the strongest protection and is what Suburban uses from the factory. Aluminum wears more slowly and is sometimes chosen for water that reacts with magnesium and causes odor. For most RVers, magnesium is the right choice.
My hot water smells like rotten eggs. Is the rod the cause?
It can contribute. Some water sources carry sulfur-reducing bacteria that react with an anode and create a sulfur smell. Flushing and sanitizing the tank as your RV manual describes usually clears it. If the smell keeps coming back, many owners switch to an aluminum anode. Don't run the heater without a rod.
How long does a rod last?
It depends on your water. In hard or mineral-rich water a rod may be used up in one season. In softer water it can last several years. Checking every 6 months tells you exactly where yours stands.
Do I need thread-seal tape?
Yes. 2–3 wraps of PTFE tape seal the tapered threads and make the next removal easier. The threads still bite through the tape for good metal contact. Avoid anti-seize compounds that aren't rated for drinking-water plumbing.
What size socket do I need?
A 1-1/16" six-point socket. A deep socket with a short extension makes it easier to reach. The socket isn't included.
My old rod won't come loose. What should I do?
Make sure the heater is cool and the pressure is released, then use a breaker bar for steady, even force. Avoid impact drivers and heat, which can damage the tank fitting. If it still won't move, an RV service shop can remove it safely.
Can I leave the rod out over the winter?
It's better not to. Drain the tank, then reinstall a rod so the port threads don't rust while the RV is stored.
Give your water heater
a longer life
Two rods, an exact fit, and everything you need to seal them in. Ready for this season and the next.
Get the 2-pack
